Hi,
I need update my RAID Controller, but I can't update by EFI. The command is not recognized.
After doing some research, I realized that my EFI is in version 1.1 and needs to upgrade to version 2.0 or higher (S5000 PSL)
How can I do this?
↧
Update EFI S5000 PSL
↧
How to reset the superuser password for RMM2.
"Slight" problem. We lost the superuser password for one of our RMM2. I cannot find any procedure in any of the available documents, on how to reset the admin superuser password for this above module. Unfortunately no other users are defined on the RMM2.
Question: how to reset the superuser password on the RMM2? The server is physically accessible.
No jumpers on the RMM2
↧
↧
non standard ipmi commands
Is there a document that defines the non standard (oem?) IPMI commands for the use with the server board S2600WT2R.
I'm looking for how to access the I2C on a PCIe card to read some sensors on the board.
I'm using the ipmitool raw command.
↧
Firmware update to SAS drives connected to RS2BL040
How do I update SAS drive firmware when the drives are attached to a RS2BL040? I don't see this capability in RWC2 or the RAID BIOS. I have 4 Seagate drives, but one is down 1 firmware revision level, so I want to update it. SeaTools for Windows won't see the drives through the RAID controller, so I'm kind of stuck. Any help please?
Thanks.
↧
swapping Intel raid cards- porting RAID arrays
Hi Everyone
I have an Intel RAID card RT3WB080 which has two RAID5 arrays of 4 x3TB drives each, total 8 drives, installed on my workstation.
I have a spare Intel RAID card RS2WG160 with SSD cache key installed, that supports upto 16 drives.
I want to port my 2 RAID arrays to the spare card on the same desktop and expand the array.
Is this possible without destroying / recreating the array.
Look forward to your input and suggestions.
Thanks
Gurvesh
↧
↧
All power supplies has "Unknown Device"
All power supplies has "Unknown Device"
SCM1, SCM2, SWM1, SWM2 removed for testing...
↧
What size of A2U44X25NVMEDK bay ?
Where can i get size of A2U44X25NVMEDK bay ?
↧
Does S2600CP4 support E5-2689 SR0L6 processor? does it have IPMI builtin or I'll need the RMM 4 module?
Hi,
Does S2600CP4 support E5-2689 SR0L6 processor?
It's not listed in the compaible processor list but would like to make sure before purchase.
Also does the board have IPMI builtin or I'll need the RMM 4 module? RMM 4 or Lite or any will work?
Thanks,
↧
RS2SG244 "latest" firmware, v12.14.0-0185 or 12.13.0-0105 ?
RS2SG244 with 22 SATA drives connected. Updated to "latest" firmware, v12.14.0-0185 now half the drives don't appear. Then I noticed that there is a "High port count" firmware which is only at version 12.13.0-0105 Both are listed as compatible with RS2SG244. Should I have installed 12.13.0-0105 instead, and if so is there anything I can do about it now?
↧
↧
Bluff Creek S5500BC and 8 GB of memory
Hello! We have the server Intel Bluff Creek S5500BC motherboard, 16 GB memories and 1 processor. There was a need to increase memory to 32 GB. Bought 4 modules on 4 GB, inserted into the motherboard and she didn't see them. After that exchanged these modules for modules on 8 GB, inserted instead of old and the server gave an error message: "Memory DIMM size invalid". What shall I do?
↧
S1200SPO SGX not available in BIOS
I'm trying to enable SGX on a S1200SPO MB with an E3-1270. I asked in the SGX forums here: SGX support for S1200SPO
The BIOS version is: https://downloadmirror.intel.com/26334/eng/ReleaseNotes_BIOS_R01.02.0023.txt..
Interestingly, there is a line in there: 03. [EPSD100028435] Delete SGX Option in setup.
How do I enable SGX on this motherboard? Is there a special BIOS update?
Thanks,
Josh
↧
Using an Adaptec 7805Q with an S1200V3rpl and P4304XXSHCN
Hi
I have the following;
Intel S1200V3RPL Motherboard
Intel P4304XXSHCN Enclosure with a 4 bay HotSwap 3.5" module
Adaptec 7805 RAID controller with aHDmSAS to 4xSATA and 1 SGPIO 5pin x2 row socket with 8 wires connected,
The Hotswap module has a backplane which has 4 SATA connectors on it, it also has an SGPIO, I2C_IN and I2C_Out sockets.
The Motherboard has the correct connectors on for the SGPIO cabbles supplied.
The SGPIO socket on the backplane is different from the SGPIO connector on the Adaptec cable
My questions are
I understand that the SGPIO provides status information to the LEDs of the hotswap bay.
1. Does the SGPIO on the backplane need to be connected to the Adaptec 7805 or can it be connected to the S1200 Motherboard?
2. What are the I2C_In and I2C_OUT conectors for
3. There will be no loss in performance if no SGPIO cable is connected (Just no status LED info?)
Looking forward to some help
↧
i3-6100T compatible with a S1200SPL?
i3-6100T compatible with a S1200SPL?
It's just not listed under the Compatible Products tab.
↧
↧
Mi Server S5520SC no me reconoce el teclado USB no pasa de la pantalla precione F1 o F2 para entrar al SETUP que puede ser
Mi SMi Server S5520SC no me reconoce el teclado USB no pasa de la pantalla precione F1 o F2 para entrar al SETUP que puede ser
Mensaje editado por: WolfCuba Garcia
↧
How to reset the superuser password for RMM2.
"Slight" problem. We lost the superuser password for one of our RMM2. I cannot find any procedure in any of the available documents, on how to reset the admin superuser password for this above module. Unfortunately no other users are defined on the RMM2.
Question: how to reset the superuser password on the RMM2? The server is physically accessible.
No jumpers on the RMM2
↧
Does S2600CP4 support E5-2689 SR0L6 processor? does it have IPMI builtin or I'll need the RMM 4 module?
Hi,
Does S2600CP4 support E5-2689 SR0L6 processor?
It's not listed in the compaible processor list but would like to make sure before purchase.
Also does the board have IPMI builtin or I'll need the RMM 4 module? RMM 4 or Lite or any will work?
Thanks,
↧
Help Me! Model S2600CP
Hello dear users! Help me please to launch my S2600СP server.
I have this problem:
It was installed system Windows Server 2008 x64 R2. Very noisy coolers and I decided to update the BIOS to automatically adjust the noise coolers. I downloaded the update "S2600CP_SFUP_BIOS02060002_ME020107328_BMC0125r9398_FRUSDR111" and set them with the windows command line. Update was successful, but after I turned off the server and turn it on again, it is no longer loaded, again noisy cooler and there is no signal on the monitor.
I read the instructions, move the jumper to position 2-3 and would like to install the BIOS firmware from the flash drive, but I did not work, writes: BIOS INSTALLED: SE5C600.86B.02.03.0003
Platform ID: S2600CP
And flashing cursor to the bottom, no processes not.
I ask your help, please tell me what should I do?
↧
↧
non standard ipmi commands
Is there a document that defines the non standard (oem?) IPMI commands for the use with the server board S2600WT2R.
I'm looking for how to access the I2C on a PCIe card to read some sensors on the board.
I'm using the ipmitool raw command.
↧
Intel BIOS Firmware update package DOESN'T support INTEL Xeon
Hello
Thank you for your email, see below.
Board E51976-406
Serial no: AZGP05000111
BMC 1.23
HSC0.00
ME 06.00.30.1119
SDR 0.18
BIOS S3420GP.86B.01.00.0046
BIOS Build date 09/29/2010.
Before proceeding with BIOS update for Intel® Server Board S3420GPLC reading the important notes section I see the following.
The system BIOS revision provided in this software update package does not include processor microcode to support any production Intel(R) Xeon(R) processors.
Also when running EFI I'm advised to run BMC & FRUSDR before updating the BIOS. I didn't proceed to install update.
I'm TOTALLY confused. I have Xeon processor.
If I install S3420GPLX/LC Firmware Update Package for EFI fully package how will this affect Xeon processor?
Thank you for your help.
Hello Christopher,
Thank you for your email. I do not
see an S3420GPC board in the ARK product catalog, but the S3420GP TPS document
refers to the LC SKU as “S3420GPC”, so what you have may be the S3420GPLC: http://www.intel.com/content/dam/support/us/en/documents/motherboards/server/s3420gp/sb/s3420gp_tps_r2_4.pdf
You can download the BIOS update from
the “Download Drivers” menu option on the left side of the product page.
http://ark.intel.com/products/46533/Intel-Server-Board-S3420GPLC
If you do not see the software you are
looking for in the ARK driver list, you can search the Intel Download Center
website for your board model to see more options.
https://downloadcenter.intel.com/
If you require further assistance, Intel
Customer Support can be reached through the following site:
http://www.intel.com/content/www/us/en/support/contact-support.html
Regards,
Lori Yung
ARK Support
- ark.intel.com
↧
Motherboard s5520ur need a RAID controller (Материнская плата s5520ur нужен RAID контроллер)
Eng: Motherboard s5520ur need a RAID controller which supports SAS hard disk volumes 1,8Tb, currently worth Raid Controller RS2BL080 he does not find them. Tell me which controller is suitable for this motherboard?
RUS: Материнская плата s5520ur нужен RAID контроллер который поддерживает жесткие диски SAS объемем 1,8Тб, на данный момент стоит RAID контролер RS2BL080 он их не обнаруживает. Подскажите какой контроллер подойдет для этой материнской платы?
↧