Hi I have a Intel S2600TPR server and need the latest raid driver to install windows 7 64bit OS. I've tried the drivers froms support but they seem to be out dated and not funtional. Urgent assistance needed...
↧
Intel S2600TPR server + latest raid driver to install windows 7 64bit OS.
↧
Help activating Intel Modular Server LUN Copier Key
Since the imskey.intel.com activation site is no longer functional, where can i activate my LUN Copier key?
I have the CMM and Paper Pack ID available for activation
thank you,
↧
↧
While installing Vmware Esxi 5.5 on Intel S2400BB. It does not detect Hard drives.
Hi everyone,
I have above specification server. I am facing problem when installing Wmware Esxi5.5 or any lower version of Esxi. During installation Esxi detect no hard drive it show like this.
So Please guide me how can i fix this problem.
Thank
↧
Intel Active System Console - Data is being retrieved, Please retry
ASC gives the above message. I have removed ASC and RAID Web Console. Rebooted and installed ASC only. I have waited a day and still get the same message.
OS is Windows Server 2012
Server board is S5520HCR
Can anyone help please?
↧
S5520HC blocks traffic
Hi. There is a server with the matherbord S5520HC, Windows Server 2008 r2 and several virtual machines on a Hyper-V. There are two network cards on the server, the first one is used directly by the server, another one is for the virtual machines.
There is a serious problem with blocking traffic from some of the computers on the network to the server and all the virtual machines. In case if I change IP address of the computer it discovers the server and all virtual servers for a while but later traffic blocking is enabled again. I assume that happens due to Trusted Execution technology. I have tried to turn it offin the BIOS but I have found the only "Execute disable bit" option. If I turn off this option - the virtual machines can be run due to not running the hypervisor.
I need your advice how to turn off the traffic blocking?
↧
↧
OpenCL support for Xeon Phi?
OpenCL™ Runtime 14.2 for Intel® CPU and Intel® Xeon Phi™ Coprocessors is marked as deprectaed and newer versions seem to only support CPUs.
Is there an update coming?
↧
S3420GPLX with 32GB RAM configured
Hi,
We have 2 servers with S3420GPLX motherboards (3 of 2 banks). I can't find this motherboard model in your memory configuration tool.
According to this document http://www.intel.com/content/dam/support/us/en/documents/motherboards/server/s3420gp/sb/s3420gp_userguide1.pdf we should be able to upgrade our 2 servers with up to 32GB RAM each.
Sadly for us, Intel documentations is quite poor/old so there is no 8GB memory stick listed in their tested hardware document http://download.intel.com/support/motherboards/server/s3420gp/sb/serverboards3420gplx.pdf
So even when 32GB should be supported, there is no Intel documentation that tells with which modules you can reach that 32GB (3 x 2 banks).
I see other posts asking this question but no memory module is finally recommended. Most close to an answer, is a link to kingstone configurator for discontinued memories. Any help in what memory to buy?
Thank you very much
Seb
↧
who knows Intel server naming rules?
Does anybody know the naming rules for intel server? like R2208WT2YS、R2208WTTYC1R?
↧
S5500BC Power control fault
What should I do if the server board
S5500BC leave a beep code Power control fault 1-5-4-4. What should replace serverboard? I've tried with a new Power Supply but still gives the same error message.
↧
↧
Материнская плата s2600KPF не могу настроить SOL
собственно вот
[root@head~]# ipmitool -H X.X.X.X -U ADMIN sol info 1
Password:
Info: SOL parameter 'Nonvolatile Bitrate (5)' not supported
Info: SOL parameter 'Volatile Bitrate (6)' not supported
Set in progress : set-complete
Enabled : true
Force Encryption : false
Force Authentication : false
Privilege Level : USER
Character Accumulate Level (ms) : 60
Character Send Threshold : 96
Retry Count : 7
Retry Interval (ms) : 500
Volatile Bit Rate (kbps) : IPMI-Over-Serial-Setting
Non-Volatile Bit Rate (kbps) : IPMI-Over-Serial-Setting
Payload Channel : 1 (0x01)
Payload Port : 623
Пользователь ADMIN является администратором в ipmi.
[root@node01 ~]# ipmitool -H node01-ipmi -U ADMIN sol set non-volatile-bit-rate 57.6
Password:
Error setting SOL parameter 'non-volatile-bit-rate': Parameter not supported
подскажите где проблема.
↧
S1200V3RPL: BMC turns off
Hello All !
S1200V3RPL (the new board) with the "Remote Management Module AXXRMM4Lite" module installed. BIOS updated to the latest version.
Board has a strange behaviour: when turn it off thought Web Console it turns off completely, with the BMC. There is only one LED on the board, that always lights (green) -- power (near the main power connector). LEDs on both NICs, status and ID (rear) all turned off. It goes without saying, that there is no ping and network connectivity to the Integrated BMC Web Console.
The BMC starts working when press on the Power Button on the front panel. System stays in the off mode, only the BMC turns on, initializes and work in ordinary mode (like when one turns on power source).
I tried:
- To reflash firmware for the BIOS, BMC and ME using according recovery modes (in sequence, one by one, setting according jumper with full AC power down, like it was mentioned in Recovery notes);
- to downgrade BIOS to the v03.01.0002;
- run the board with the other power source.
↧
Help activating Intel Modular Server LUN Copier Key
Since the imskey.intel.com activation site is no longer functional, where can i activate my LUN Copier key?
I have the CMM and Paper Pack ID available for activation
thank you,
↧
2 sockets Broadwell vs 4 sockets Opteron
is it possible for a E5-26xx v4 in a 2s board to compete equally against AMD Opteron 6344s in a 4s board?
Checking Specs results (mainly CPU2006), I found several e5-26xx skus that easily double the Opteron 6344 ratings in all aspects, running on all chips, would that be enough to compare the performance of both systems?
Or am I completely misunderstanding Spec results?
Thanks!
↧
↧
How do I update the BIOS on a very old S2600CP motherboard?
Hi,
I've just been given an ancient, refurbished S2600CP2J motherboard complete with CPUs and RAM and would like to get it fully working again.
The obvious first step is to update the BIOS but the oldest EFI update package available (01.02.003) states that I need to have at least version 01.01.1002 before starting or "the update process may render the system not operatable!"
According to the BIOS screen, my system is currently SE5C600.86B.99.99.x034, build date 08/23/2011.
As I have no wish to kill the system before I get started, is there any way of upgrading it to 01.01.1002 as a minimum?
Thanks.
↧
Intel S2600TPR server + latest raid driver to install windows 7 64bit OS.
Hi I have a Intel S2600TPR server and need the latest raid driver to install windows 7 64bit OS. I've tried the drivers froms support but they seem to be out dated and not funtional. Urgent assistance needed...
↧
Failure: S3420GPV cannot handle Hard Drives larger than 2TB in AHCI Mode
Hello,
we urgently need help... any ideas?
we have Problems with two identical 4TB harddisks. we use the harddisks only for datastorage, no booting. No RAID.
Only AHCI mode!
The server recognize the 4TB on each drive. When dataspace reach more than 2TB data amount, drive controller get the failure.
It seems that, when we store more than 2TB on the 4TB harddrives, die GPT partitiontable changes to the volume to RAW format and the data get lost.
We use 2 drives, we tested each harddrive. Both drives seems to be ok. And we can reproduce the failure
System Error log found a controller ERROR, Disk , ID:11
Motherboard: S3420GPV S1156
Operating System: Win2008 R2 SP1
BIOS Version: S3420GP.86B.01.00.0053.081120151728, BIOS Date: 08/11/2015
AHCI-MOde check seems ok,
INtel(R) 5 Series/3400 Series SATA AHCI Controller, Intel, 08.06.2010, version: 9.6.4.1002
PLease see attached SERVER01_2.HTM for more systeminformations.
It seems that Intel
S3420GPV cannot handle Harddrives larger than 2TB in AHCI mode ?
Please help, what we can do to get it running...
Feel free to contact us for further informations...
regards
↧
S5500BC Power control fault
What should I do if the server board
S5500BC leave a beep code Power control fault 1-5-4-4. What should replace serverboard? I've tried with a new Power Supply but still gives the same error message.
↧
↧
Error code 1072365566 when reinstalling Intel Active System Console when trying to set a new password.
I uninstalled the program originally since I was unsure what the original password was. It starts to install fine but after I type in the password, and click yes to bypass the weak password prompt, A box with that error code pops up. I have not been able to find much about it except for a site for IBM troubleshooting which said something about uninstalling C++ Redist 2005. I did so which then tried to install the System Console again which prompted me to install 2005 again. It then got to the same point and gave the same error code. I have also rebooted the server which did not seem to help. The server in question is an Intel S3420GP running Microsoft Windows Server 2008 R2 Standard. Thanks for any help.
↧
S5520HC blocks traffic
Hi. There is a server with the matherbord S5520HC, Windows Server 2008 r2 and several virtual machines on a Hyper-V. There are two network cards on the server, the first one is used directly by the server, another one is for the virtual machines.
There is a serious problem with blocking traffic from some of the computers on the network to the server and all the virtual machines. In case if I change IP address of the computer it discovers the server and all virtual servers for a while but later traffic blocking is enabled again. I assume that happens due to Trusted Execution technology. I have tried to turn it offin the BIOS but I have found the only "Execute disable bit" option. If I turn off this option - the virtual machines can be run due to not running the hypervisor.
I need your advice how to turn off the traffic blocking?
↧
S1200SPL - Windows does not see RST partition
I'm assembling a new server. New S1200SPL board. I have 4 2TB Western Digital drives. In any RAID configuration with RST, Windows 2016 Essentials does not see the RAID partitions at all. I tried all variations and tried all drivers I can find online. How can I get Windows to see the Disks so I can install the OS?
Thanks.
↧