We recently bought the S2600CW serverboard for our school and we are required to install Ubuntu 11.10 and Squid 2.7 to have the server act as a proxy server. However, our problem is installing the Ubuntu 11.10. We encountered repeating error messages. We are looking for solution or anything that can help us install Ubuntu 11.10. Thanks
Does the s1200v3rpl support cachecade?
I see it listed as an option in the RAID web console but I can't find any supporting documentation.
The s1200v3rpl is part of a P4308RPLSHDR.
Thanks in advance!
Hello everybody,
I'm currently running a single E5-2609v3 in my S2600CWT Mainboard. I just did a Bios Update to the latest Version (01.01.016 I think).
In the changelog it says it supports v3 as well als v4 CPUs.
On the ARK Page for my mainboard, it says it is only compatible with the v3.
The question is, whether my Mainboard is compatible to the newer Gen v4 CPUs?
Kind regards,
Jannik
Hello,
I've a SS4000-e with 2 hard-disks and configured as RAID 1. Now the SS4000-E have a problem. I cannot connect via the networkdrive with Windows, MAC OS and Unix.
I can login to the adminpannel over webbrowser and all looks good, but I cannot save any changes (error in browser).
So I've put the harddisk out and put it in my PC. How can I read the partition to save the data?
Thanks
Stefan
Or what is the "maximum" CPU for this board?
I have a machine that has integrated Intel HD 2500 graphics on it. I am able to find drivers for client OS's like Windows 7, 8, 8.1, 10, etc but nothing for Servers. They do detect the hardware appropriately and install but upon a reboot after installation the Windows logo starts and then everything goes black. Uninstalling the driver via Safe Mode brings Windows back up but using the Generic Graphics driver from Windows. Has anyone successfully been able to get HD 2500's to work under a server os?
I want to do a clean install of 64-bit Windows 7 Pro on the R1304WTTGSR server (S2600W motherboard). The specs for this server say Windows 7 EFI is compatible and has been tested with this server.
The specific configuration is
2 x Xeon processor E5 2630 v4
2 x 64 GB ECC LRDIMM DDR4 memory
2 x Seagate 8 TB hard drives
Panasonic BD Blu-ray drive
Radeon XFX R5 230 graphics card, installed in riser slot 1.
Mouse and keyboard connected via front USB port (using a splitter).
LAN-see below
The firmware ("BIOS") is set to boot using EFI. AFAIK, this means it cannot boot using BIOS ("Legacy") mode.
When I boot the Windows installation disk (latest version of Windows 7 x64 from Microsoft web site), using EFI, the screen shows first "Loading files", then "Starting WIndows". At this point:
- With nothing connected to the network ports (LAN), the system hangs. By "hangs" I mean nothing changing on the screen, no DVD or disk activity, no response to mouse or keyboard, and no response when front panel power button is pushed.
- With a CAT5 (Ethernet) cable connected between network ports 1 and 2, the system proceeds with some animation of the Windows flag (fading and brightening), but other than this, the system hangs as above. The reason for connecting the network ports is that someone posted that there is a bug in the Windows 7 install disk network drivers, that they hang when nothing is connected.
In either case, waits of several hours does not matter--the system is frozen.
I also thought of installing from USB drive, but without success. The Microsoft Windows7-USB-DVD-Download-Tool-Installer does not produce an EFI-bootable result, nor does Rufus 2.10.973 (the current version). I created a Windows 10 USB drive using a different Microsoft tool, MediaCreationTool, and it is EFI-bootable, but requires that I load the disk drivers.
Although it may be unrelated, the last thing I tried was resetting the BIOS to factory defaults (F9). That made my add-in video card stop working, even though it was enabled in the BIOS.
BIOS version is SE5C610.86B.01.01.0016 (3/31/2016). The server did not come with any software.
If anyone has successfully done this installation, please share the secret steps needed to do so.
Intel Server Board S1200SPL имеет том RAID1 (с ручным обновлением "По запросу")
в режиме Intel RSTe 4 (Intel Rapid Storage Technology (RST)).
Поддерживается ли в этом режиме технология Intel® Smart Response Technology?
Можно ли использовать в качестве дисков для ускорения:
1. M.2 SATA SSD (2242 form factor)
или
2. SATA DOM (Disk on Module) на порту SATA4?
Intel Server Board S1200SPL.
В режиме Intel RSTe 4 RAID1 есть ли режим обновления тома "По запросу", как в более ранних Intel Server Board?
Этот режим необходим для защиты от воздействия вирусов.
Есть ли такой режим (RAID1 с ручным обновлением "По запросу") в режиме Intel ESRT2?
В описании ESRT2_Software_UG.pdf об этом ничего не сказано:
http://www.intel.com/content/www/us/en/support/boards-and-kits/000005760.html
http://www.intel.ru/content/www/ru/ru/support/boards-and-kits/000005760.html
I have a number of S2600CWTR boards .... these boards have two 7-pin SATA ports. What do you recommend for people that need more ... is there an add-on SATA controller that you recommend?
I have an RT3WB080 installed in a personal server. On startup, the controller always logs "Information" for each drive "Invalid field in CDB". It only appears once per boot and all the drives are tested with no bad blocks.
What does this mean and how to correct it? This started appearing after I replaced failure-prone Seagate drives with new WD Red 3TB drives.
Hallo,
i try to install my own Secure Boot PK Cert but dont can find an way to remove the
pre installed. So Secure Boot runs in User Mode and i cant get in Setup Mode.
Is there a way to remove the PK key oder get Secure Boot into Setup Mode?
What i found is that some Intel Boards have the Bios Menu entry to set Secure Boot Mode to Custome but this dont.
With Keytools i dont can remove the installed PK without an auth file that i dont have.
And can i even prove that this PK is really from Intel?
Used last Updates:
BIOS ID : SE5C610.86B.01.01.0016.033120161139
BMC FW Rev : 1.43.9685
Boot FW Rev : 1.07
SDR Package Version : SDR Package 1.13
Mgmt Engine (ME) FW Rev : 03.01.03.021
Product Name : S2600CWR
Part/Model Number : H12882-260
On Board Installed: TPM AXXTPME5 (but not active)
Bios Options
Keytool
Hello!
I recently bought an used s5520hc mainboard. I tried to boot it with a 600w psu that is actually for desktopcomputers. It has only one 4-pin connector for the first cpu instead of two eight-pin connector for both cpu's. I just wanted to check if the board could boot. After a few seconds there was this beep signal: 1-5-4-4 ("Power good assertion timeout - Power unit sensors report soft power control failure offset."). Now my question is whether it is more likely that the board is bad (I read about some issues in some forums []Intel S5520HC and SR5650BRP]) or the problem can be solved by buying a sc5600 chassis with powersupplies (750w).
Hello! Can i install GTX 980Ti in chassis P4304XXMUXX ?! MB S2600CW2R, Card length 30.5 cm. Thanks.
I want to do a clean install of 64-bit Windows 7 Pro on the R1304WTTGSR server (S2600W motherboard). The specs for this server say Windows 7 EFI is compatible and has been tested with this server.
The specific configuration is
2 x Xeon processor E5 2630 v4
2 x 64 GB ECC LRDIMM DDR4 memory
2 x Seagate 8 TB hard drives
Panasonic BD Blu-ray drive
Radeon XFX R5 230 graphics card, installed in riser slot 1.
Mouse and keyboard connected via front USB port (using a splitter).
LAN-see below
The firmware ("BIOS") is set to boot using EFI. AFAIK, this means it cannot boot using BIOS ("Legacy") mode.
When I boot the Windows installation disk (latest version of Windows 7 x64 from Microsoft web site), using EFI, the screen shows first "Loading files", then "Starting WIndows". At this point:
- With nothing connected to the network ports (LAN), the system hangs. By "hangs" I mean nothing changing on the screen, no DVD or disk activity, no response to mouse or keyboard, and no response when front panel power button is pushed.
- With a CAT5 (Ethernet) cable connected between network ports 1 and 2, the system proceeds with some animation of the Windows flag (fading and brightening), but other than this, the system hangs as above. The reason for connecting the network ports is that someone posted that there is a bug in the Windows 7 install disk network drivers, that they hang when nothing is connected.
In either case, waits of several hours does not matter--the system is frozen.
I also thought of installing from USB drive, but without success. The Microsoft Windows7-USB-DVD-Download-Tool-Installer does not produce an EFI-bootable result, nor does Rufus 2.10.973 (the current version). I created a Windows 10 USB drive using a different Microsoft tool, MediaCreationTool, and it is EFI-bootable, but requires that I load the disk drivers.
Although it may be unrelated, the last thing I tried was resetting the BIOS to factory defaults (F9). That made my add-in video card stop working, even though it was enabled in the BIOS.
BIOS version is SE5C610.86B.01.01.0016 (3/31/2016). The server did not come with any software.
If anyone has successfully done this installation, please share the secret steps needed to do so.
I have a new to me H2312XXKR chassis with four HNS2600WP blades. I added RAM and CPU to one blade and tried to boot it but get no VGA signal. The same RAM DDR3 1600 and CPUs E5-2650 V2 work in another 2600WP blade just fine. This one seems to be new and never used. Is there a trick to setting up these boards for the first time?
Hello,
We installed a new server with motherboard s2600cw. The Server freezes completely and a force restart is required when virtual machines are running on SSD drivers. This doesn't happen on mechanical hard disks. We suspect some issue between the controller and the Gen2 SCSI virtual machines running on Hyper-V. Please assist.
Regards,
CompNet
I recently purchased a R2312WTTYSR and wanted to make sure I was not just missing something obvious. Is there no way to connect all 12 drives to the server without also purchasing an additional SAS expander? I would have thought that if the system shipped with 12 bays as an option that the necessary equipment would be on board to connect all 12 drives to the motherboard, and perhaps there is but I am not seeing it. Any corrections or confirmation would be appreciated before I go out and purchase a SAS expander.
Hello,
Intel Compute Module HNS2600KPF
S2600KPF mobo
2x Xeon E5-2670
BIOS 01.01.0016, BMC 1.43.9685, ME 03.01.03.021, SDR 1.14
CentOS 6.8, kernel 2.6.32-642.3.1.el6.x86_64
After reboot I have the following entry in mcelog:
Hardware event. This is not a software error.
MCE 0
CPU 12 BANK 20
MISC 100000000000000
TIME 1470234024 Wed Aug 3 16:20:24 2016
MCG status:
MCi status:
Error overflow
Uncorrected error
MCi_MISC register valid
Processor context corrupt
MCA: BUS error: 1 12 Level-3 Generic Generic Other-transaction Request-did-not-timeout
Running trigger `bus-error-trigger'
QPI: Intel QPI link layer detected control error from R3QPI
STATUS ea00000000100e0f MCGSTATUS 0
MCGCAP 7000c16 APICID 20 SOCKETID 1
CPUID Vendor Intel Family 6 Model 63
Can anybody decode this error ?
thanks in advance, Pawel