Hi everyone,
I am having an issue with a Dell R720 server.
I see tons of drivers which appears with: No drivers are installed (picture below)
I have the same on both Windows 2016 and windows 2012 R2
I've installed all I could find from Dell's website, updated all: iDrac/Lifecycle/Bios/Chipset/Drivers
Has anyone encountered this? Anyone who could guide me in the right direction?
Hello,
I've encountered the memory problem on Intel S2600CWTSR with SKhynix 64GB 4DRx4 PC4-2400T-LE1-11 modules.
The memory is listed at THOL:
SKhynix | Memory | HMAA8GL7MMR4N-UH | 64GB (1X64GB) LRDIMM, DDR4, 4 Rank, 2400MHz, x4 | Active |
Single memory modules were attached to the first memory slot (DIMM A1). Already tried several sticks.
Unfortunately, during boot process 3x beeps occurs and the system hangs at message "Chipset Initialization complete. No error found."
POST Codes:
(..) cut
00:04.980 0xB7 Train DDR4 ranks
00:04.980 0xB7 Train DDR4 ranks
00:04.980 0xB7 Train DDR4 ranks
00:04.990 0xB8 Initialize CLTT/OLTT
00:04.990 0xB9 Hardware memory test and init
00:04.990 0xB9 Hardware memory test and init
00:04.990 0xBA Execute software memory init
00:04.990 0xB7 Train DDR4 ranks
00:04.990 0xBB Program memory map and interleaving
00:04.990 0xE8
Currently using:
BMC FW Build Time : 2017-03-14 09:54:34
BIOS ID : SE5C610.86B.01.01.0021.032120170601
BMC FW Rev : 1.49.10574
Boot FW Rev : 1.07
SDR Package Version : SDR Package 1.13
Mgmt Engine (ME) FW Rev : 03.01.03.043
Restoring the BIOS default settings did not help.
Has anyone had a similar problem?
Mainboard: SC2600CP2R mainboard with 2 Xeon CPU's and 128 GB Ram, latest firmware, works perfekt.
RaidControler: RS3WC080 with 4x1TB Seagate Intel-certificated SAS Drives, latest firmware.
i am able to create a virtual device (raid-5 array with state optimal, 3 x 1 TB + 1 hotspare), but can't declare as boot-device, boot device is always "none".
This happens in boot-mode legacy (configuration with CTRL-R) and in boot.mode UEFI (configuration over PCI-Configuration -> UEFI Option Rom Control -> Storage Controler)
Installation of VMWARE 6.5 or Windows Server 2016 stops with "no boot device found"
I spend a lot of time, but can't find any error.
I would be very happy if somebody can help me
Norbert
I'm having trouble booting a S1200V3RP server board with a Core i3-4130T installed.
It doesn't sound any beep codes, and generates video as far as displaying the following:
Version 2.14.1219.Copyright(c) American Megatrends, Inc
Installed BIOS: S1200RP.86B.03.01.0002
Platform ID: S1200RPS
After a few seconds, the status LED on the motherboard begins flashing orange. The diagnostic LEDs show a code of 00101011 which doesn't appear to be documented (it was mentioned in another thread here, but never resolved).
CPU is a Core i3-4130T which appears to be fully supported with this board and BIOS. Both board and CPU are new.
I have tried three different RAM modules that should all be supported, and have installed in slot A1 for troubleshooting.
Removing the RAM generates a three-beep error code as expected; likewise, removing the CPU generates 1-5-2-1.
Can anyone provide further troubleshooting advice? Thank you in advance.
Dan
服务器重启以后找不到系统盘，设置了启动项后保存可以进系统，再次重启以后启动项就会自动变更，然后就找不到系统盘
Hi all,
I want to upgrade my servers`s ram, the motherboard is a supermicro X10DRi-T4+, it has 2 physical CPU`s E5-2690 v3, I currently have 256 GB and I want to max out the memory.
The question is, can I upgrade to 768 RAM x 2, as the max memory for CPU is 768 , while the motherboard has a max limit of 3 TB, or 384 RAM per CPU.
All the documentation I found points to 768 per CPU, but I would like to have another confirmation before buying the RAM.
Thank you.
Tara.
Every time I need to restart the two Windows Server 2016 Datacenter boxes I have the RS3DC080 card installed on, the driver is disabled under Device Manager -> Storage controllers. I have the latest 6.713.5.0 drivers for Windows 10 x64 installed per the instructions. Any help would be appreciated as it takes a few moments to remember that disabling and re-enabling the device solves the issue (but requires manual intervention).
Thanks.
I have a system with an S2600CP motherboard and 2 identical hard drives in RAID1 using ESRT2. I went into the ESRT2 configuration utility attempting to remove the RAID while keeping the data on the drives intact, so that I could use one of the drives separately. I read some instructions that I think were for a different type of RAID technology, and accidentally cleared the storage configuration. Now I can't boot from the drives and I'm worried that if I create a new storage configuration it will initialize (meaning wipe?) the drives. The ESRT2 manual doesn't seem to mention a way to create a new configuration without initializing the drives. The BIOS also cannot see the drives at all because they are connected to the ESRT2/RSTe SATA ports and not the normal SATA ports. Should I try plugging one of them into a normal SATA port? How can I recover the data? Since this is a RAID1 and there is no striping I don't see how the data could be permanently lost, right?
Hi,
I'm building a Windows Server 2012 R2 system using some existing server parts that we have available. I started with one S5500BC board and added the required hardware, which is an LSI 9260-8i card (this card was already in a number of old servers we have with the same board and worked fine) and I've added an Intel I350-T4 network card and a 2 port USB 3 card. I have done the exact same upgrades / additions to 2 other servers based on the same S5500BC boards and Server 2012 R2 and neither of those other 2 servers have any issues.
So with this build, the server lost power 2 nights in a row, windows just logging the standard 'kernel power' error, which is as if the plug was pulled (but it wasn't). After the second night of this I installed the Intel ASC and it told me there was an uncorrectable ECC issue in dim slot B1. I powered down the server and moved the RAM about and it still reported the same error in the same slot. I did this a couple of times to be sure and it always reported DIMM slot B1 as the problem, regardless of what stick was in it. I took this to mean that the motherboard itself was faulty so I replaced the whole board with another S5500BC we have spare. This is a working board that also (like the first one) has never given any reason to believe there are any problems with it.
After putting the second board in, I ran the ASC again and the same B1 error was present. I thought the may be the ASC calling up the old logs so I uninstalled and reinstalled it, and the memory error was gone. I checked it after around 12 hours of the server running and this remained the same. However a couple of nights ago the server again 'lost power' or just shut down ungracefully. I check the ASC again, and the same B1 error is back! On a completely different board.
What could be going on here? I quite urgently need to get this server stable. I have tried to update the firmwares using the S5500BC_BIOS63_BMC61_FRUSDR22_ME112 package, I ran the one boot windows flash utility (v9.7 build 21) pointing to the extracted location using the following command:
flashupdt -u C:\TempPath
But I get the following:
Update file configuration: XXX S5500BC,1.0
*ERROR* BMC responded with incompatible values
Could anyone please help? The only thing that is different about this server to the other 2 that are stable is that this one has 8 drives instead of 6. But it had 8 drives anyway during it's previous installation and there were no issues... ??
Thanks.
Hi,
we have several new Servers with the S2600WTTR Mainboard (System BIOS - R01.01.0021 and R01.01.0022).
When we connect a USB 3.0 Disk (WD Elements 2TB), the server beeps and restarts.
Beep Code: 1-5-4-2
Associated Sensor: Power fault
Reason for Beep: DC power unexpectedly lost (power good dropout) -Power unit sensors report power unit failure offset...
In the BMC Server Health log i have this entries:
| 8 | 07/21/2017 16:11:06 | Pwr Unit Status | Power Unit | reports the power unit has suffered a failure - On-board 5V and 3V3 Power failure, - Deasserted |
| 227 | 07/21/2017 16:11:05 | Pwr Unit Status | Power Unit | reports the power unit is powered off or being powered down - Deasserted |
| 226 | 07/21/2017 16:11:00 | Pwr Unit Status | Power Unit | reports the power unit is powered off or being powered down - Asserted |
Update:
I have this problem on Servers with Vmware installed / also on Systems with Windows - Do i need to check some Bios Settings ?
If the Server stands on BIOS Screen and you connect the USB Disk, also a power fault occure and the server restarts...
Any ideas ? any help is appreciated! Thanks in advance!
Why are the fans running high? No lights on by the fans are on and the power supplies lights are green.
This was running fine last week. Tried update the firmware/BIOS to 02060006 and problem remains.
The logs indicate various issues of the PS1 & PS2 not having enough voltage then they are fine; CPU #2 is not connected; Fans are not redundant. What is the real issue here?
Hello, I have a problem. Server board Intel SE7520JR2 with the old version BIOS BMC (version 20). I can not update the firmware to v.52, because new updates are working starting with version 23. Please help me find the firmware BMC ver. 23 for SE7520JR2.
"BMC 0.23 or later must be preinstalled.
If this is not the case, please update the IMM firmware to BMC 0.23 before
updating to this release.
The boot block has been changed with the BMC 0.31 release but it is not
required for this release. The batch file provided with this BMC package
does not update the boot block."
Dear Intel Support,
My system has following configuration: Mainboard S2600CW2R, Chassis P4304XXMUXX with two PSUs FXX750PCRPS, two CPUs Xeon E5-2637V4, Memory 8 modules each 16GB, one SSD DC S3520 Series 480GB, one HDD Seagate 3.5" 8TB ST8000NM0045 and Graphic Card ASUS GTX 1080 Ti.
OS: Windows 10 Pro. All firmware was initially updated to the newest version.
System works properly, passes all tests, OS boots and runs OK.
When starts 3D modelling software Bentley Context Capture and Graphic Card is in full load, system is suddenly shutting down with beep code 1-5-4-2.
PSUs are in FULLY_REDUNDANT state.
Looks like insufficient PSU resources.
"S2600CW_H56450_P4304XXMXXX_power budget_tool R1.1" tells that there is enough PSU resources: System Totals: 647W; Power Supply Limits: 750W.
Could you please advise me what the possible cause of system shut down and which actions to be taken to resolve situation?
Maybe to set PSUs in NON_REDUNDANT state to gain available power resources?
But I've found none information in a lot of manuals available how can I make it.
Thanks in advance.
I have a system with a S2600CP2J board. I would like to enable its KVM features by adding a remote management module that works with this board (AXXRMM4 or AXXRMM4LITE).
Since I don't necessarily need a dedicated NIC for remote management, I'm mostly looking for the AXXRMM4LITE. However, I'm having a hard time finding one in stock (in the EU).
AXXRMM4LITE2 seems easier to find but isn't compatible with the S2600CP2J board, according to the Intel site here: Remote Management Module 4 Lite 2 AXXRMM4LITE2 Product Specifications
The AXXRMM4LITE2 module does look identical to AXXRMM4LITE (unless the pictures online are wrong), so I was wondering if anyone knew if it could be compatible after all?
Hi,
Problem: When starting ESXI, the error message "Fatal Error: 10" occurs and the VmWare does not start.
I found this with VmWare and have this also in the BIOS set up:
"To workaround this issue the BIOS setup option to allocate the MMIO space required by adapters in the memory space above 4GB."
But the problem remains.
Configuration:
VmWare ESXI 6.5.0a
R2208WTTYSR
RMS3CC080
2x SSDs RAID 1
4x SAS HDD RAID 5
1x SAS HDD Spare
The RAID module finds the SSD and the HDDs. The ESXi can also be installed on the SSDs with RAID 1.
Does anyone have an idea why the ESXi does not want to start?
Many thanks in advance.
Jens
Good day to all.
When the server is turned on, the information on the monitor is not transmitted, the periphery does not work.
There is a polling of the hard drives, after that the server gradually increases the fan speed to the maximum.
In RMM3 error:
Pwr Unit Status | reports the power unit is powered off or being powered down, reports there has been a soft power control failure, reports the power unit has suffered a failure | 0x0061.
In logs:
| 229 | 08/18/2017 13:29:16 | Pwr Unit Status | Power Unit | reports the power unit has suffered a failure - Asserted |
| 228 | 08/18/2017 13:29:10 | Pwr Unit Status | Power Unit | reports the power unit is powered off or being powered down - Asserted |
| 227 | 08/18/2017 13:29:05 | Button | Button / Switch | reports the power button has been pressed - Asserted |
| 226 | 08/18/2017 13:29:03 | Button | Button / Switch | reports the power button has been pressed - Asserted |
| 225 | 08/18/2017 13:28:55 | Pwr Unit Status | Power Unit | reports there has been a soft power control failure - Asserted |
| 224 | 08/18/2017 13:28:50 | Pwr Unit Status | Power Unit | reports the power unit's AC is lost - Deasserted |
After turning off the button, sound signals are heard, to decode the error of the power problem.
Resetting the BIOS does not help.
Power supplies were replaced from another server - there is no result.
Changed the board into which the power supplies are inserted to the same from the production server - there is no result.
A month before, there was an error in the logs:
| BIOS Evt Sensor | System Event | reports Timestamp Clock Sync. Event is one of two expected events from BIOS on every power on. - Asserted |
After resrart the server boots up normally.
What can I do to restore the server?
I am looking at using the S2600TPR board for a project and I have a few questions:
1. Can all 4 riser slots be used as a PCIe expansion slot or have a riser card to make a PCIe expansion slot?
2. Can the mezzanine port be converted to a PCIe expansion slot?
3. Does the Intel S2600TPR board support VMware ESXi?
Hi all,
I want to upgrade my servers`s ram, the motherboard is a supermicro X10DRi-T4+, it has 2 physical CPU`s E5-2690 v3, I currently have 256 GB and I want to max out the memory.
The question is, can I upgrade to 768 RAM x 2, as the max memory for CPU is 768 , while the motherboard has a max limit of 3 TB, or 384 RAM per CPU.
All the documentation I found points to 768 per CPU, but I would like to have another confirmation before buying the RAM.
Thank you.
Tara.
Ihave installed software stack on centos 7 for intel xeon phi 7120p , everything are succed , micctrl -s gives output mic0 ready ( online ) , my question is how to run this coreprocessor with the other 2 intel xeon e5-2603 v3 in the host server , so that ican manage phi as main processor .??
Every time I need to restart the two Windows Server 2016 Datacenter boxes I have the RS3DC080 card installed on, the driver is disabled under Device Manager -> Storage controllers. I have the latest 6.713.5.0 drivers for Windows 10 x64 installed per the instructions. Any help would be appreciated as it takes a few moments to remember that disabling and re-enabling the device solves the issue (but requires manual intervention).
Thanks.