s2400gp2 network card
I have s2400gp2 motherboard and QLogic Corporation NetXtreme II BCM57840 and card not work. Its possible to work card with this motherboard?
View ArticleRAID Bios not available on S1400FP
Hello, i tried setup a RAID1 on S1400FP, i use 2 SSD 850PRO Samsung on the SATA Port 0 and 1, if i set the SATA to Enhanced i can see both SDDsEFI optimized Boot ist disabled, Quit boot is disabled,...
View ArticleS2600CW2 board and LAN port failure
We have one server with S2600CW2 board and it has few issues with LAN port1:When restarting server, BMC link fails for some period and then up again.Using LAN port 1 not possible to do anything.Have to...
View ArticleIntel Accelerated Storage Manager installation on Windows Server 2016 Core
Hi I need to install Intel Accelerates Storage Manager to Windows Server 2016 Core and mainly to silently configure monitoring/sending emails when problem with HDD occured. I didnt find any manual,...
View ArticleClik here to view.
Intel MFSYS35 Check Storage Controller Status.
Hello everybody! Here is the problem: dashboard shows this message: "Check Storage Controller Status". When I click the SCM2 in management interface it shows: "Initializing (Offline)".Our distribuitor...
View ArticleClik here to view.
Server Platform S5400SF
Hi .. anyone knows whether the S5400SF platform supports Windows 2008 R2 (64Bit) in EFI mode ?
View ArticleMFSYS25 Activate Features
Hello,I have Blade Servers on MFSYS25, and I need at least activate Advanced Management Pack (MFSADVMGMT) for SysLog feature.In a good case, I need the same for Shared LUN (MFSLUNKEY).Our distributor...
View ArticleClik here to view.
s2600cp BMC error help
I picked up a s2600cp that I am trying to get running. I have got the BIOS updated to the latest version (02.06.0006) after stepping through many upgrades. I have 3 4pin fans plugged into system fan...
View ArticleClik here to view.
84F2: BaseBoard Management Controller failed to respond
После выключения и включения сервера стартуют все вентиляторы на полную мощность.В Bios появилась ошибка 84F2.Как исправить с чем может быть связана? After the server is turned off and on, all the...
View ArticleClik here to view.
RAID question
Hello, I am not very knowledgeable about RAID, but I have a RAID server that seems to have gone bad. It contains 2 HD's @ 2 TB each in a RAID array. I believe it is the OS of the server that has gone...
View ArticleW2600CR - no video + POST beep
Hey everybody, I desperately need qualified help. I recently tried to assemble a budget workstation on the basis of the Intel W2600CR mainboard with 2x Xeon E5-2670 cpus.But I am not able to get the...
View ArticleWolf Pass Server 2600WFT Enumerates X710 PCI domain 10000 - DPDK will not load
I have a Wolf Pass 2600WFT Server where I am trying to load a DPDK-assisted vSwitch as I do on the Wild Cat Pass.But DPDK fails to load because the Ethernet port is on PCIe domain 10000, instead of the...
View ArticleHPC S2600BP - System Cards
Listed below are the Queries, 1. Are the System Boards ( Interface Cards) Similar to the ones in a 2U system Or are the HPC node based System Card's Different ? 2. Related to the HSBP of the 4 Node...
View ArticleVGA problems S1200kpr
after i have disabled onboard VGA,I'm unable to enable again,even if i enable it in bios it still dont work
View Articles1200v3RP video card problem
my motherboard (s1200v3RP) work correctly with discreet video cards GeForce GT430 and GT730 but don't want work with GTX 750ti (with ad power) and RX560 (without ad power).Any body know WHY? Please...
View ArticleHello everyone! We have P4308CP4MHGC server. There blinking orange "!" sign...
H@ello everyone! We have P4308CP4MHGC server. There blinking orange "!" sign on front panel. What it means? Thank you
View ArticleClik here to view.
Which std. (ITX/ATX) server (/or workstation) mobo for ESXi 6.5
Hi guys. Building a server used for SOHO back office and high end test/devel I want the board to support ESXi 6.5 fully NICS, I/O passthruough. Furthermore it should: 1) have IPMI/iKVM2) Support at...
View ArticleSDPTool set boot mode to uefi
Hello everyone, I just started using SDPTool for setting up server to uefi boot mode. My issue is that I can't find the correct syscfg arguments as below: SDPTool <ipv4> <username>...
View Articles2400gp2 network card
I have s2400gp2 motherboard and QLogic Corporation NetXtreme II BCM57840 and card not work. Its possible to work card with this motherboard?
View ArticleRAID Bios not available on S1400FP
Hello, i tried setup a RAID1 on S1400FP, i use 2 SSD 850PRO Samsung on the SATA Port 0 and 1, if i set the SATA to Enhanced i can see both SDDsEFI optimized Boot ist disabled, Quit boot is disabled,...
View Article