Memory Bandwidth on HPC system
Hi all,I am having a problem with the performance of our system (256GB RAM, CPU E5-2680 v3 @ 2.50GHz, Xeon Phi 7200q). When I check the performance with Linpack tool, the result is not stable,...
View ArticleS3420GPV RAM options (very confused)
I've been looking to build a server and I have an S3420GPV which I want to use, however the RAM requirements are extremely confusing for me. On the technical document, it says no support for x4 or x16...
View ArticlePower failure - Server System R1304GZ4GC
Hello there, I had a lovely working server until today, I wanted to add a internal ssd into the case so I had to get the power supply for it. There is a OSD connector there for power so I found a...
View ArticleXeon Phi 7290 - Maya Render
Hi I am a 3D Generalist. I use Autodesk Maya and Vray. I want to know if Xeon PHi 7290 supports Maya and Vray rendering. If it supports i want to buy Xeon Phi 7290.Any suggestions ?
View ArticleAdd additional Fans to P4000XXSFDR
Simple question! With the system set to performance (S1200SPL board), the fans are quite loud. Does anyone know if I can add additional fans to the P4000XXSFDR chassis? The MoBo supports additional...
View ArticleClik here to view.
Correctable ECC. CPU: 1, DIMM: B1. - Asserted
Our customer reported they have deployed several R1000 servers for broadcast service, they said the issue was occurred one time on 3 servers, this error was being asserted during 3 months from at that...
View ArticleClik here to view.
RS2BL040 unable to save power savings settings.
Setting won't save. Says invalid arguments in command. Anyone run into this? Thanks,
View ArticleClik here to view.
S2600CW - After System Boot Process "C7"
We have a new server with the S2600CW motherboard. After the system boot process is complete, there is a "C7" character that remains in the bottom right hand corner of the screen. This only shows...
View ArticleC600 RAID 5 with SSD drives cause single drive failure under heavy load
I have a Intel Server P4000CP with C600 RAID controller. I have five SSD drives (Samsung 840 PRO 256 GB), configuration - one system drive and 4 RAID 5 drives. I am running Windows 2012 R2. All drivers...
View ArticleClik here to view.
Two graphics cards ASUS HD7970-DC2-3GD5 on a S2600IP
Good morning everyone,I would like to know if any of you have already installed two graphics cards ASUS HD7970-DC2-3GD5 on a machine S2600IP with Windows 7.The two processors have 16Gb of RAM...
View ArticleHow to setup RAID on RMS3VC160 in Server R2224WTTYSR-not seeing drives!
We are new to Intel Servers, previously having HP Servers and I am finding the intel server not nearly as intuitive as the HP when it comes to setting up a RAID option. I have set up our server by...
View ArticleClik here to view.
Power failure - Server System R1304GZ4GC
Hello there, I had a lovely working server until today, I wanted to add a internal ssd into the case so I had to get the power supply for it. There is a OSD connector there for power so I found a...
View ArticleClik here to view.
Blade System zeigt einen Fehler - PS Slot #4 Output Voltage: Upper Critical...
Blade System zeigt einen Fehler - PS Slot #4 Output Voltage: Upper Critical sensor threshold asserted
View ArticleC600 RAID 5 with SSD drives cause single drive failure under heavy load
I have a Intel Server P4000CP with C600 RAID controller. I have five SSD drives (Samsung 840 PRO 256 GB), configuration - one system drive and 4 RAID 5 drives. I am running Windows 2012 R2. All drivers...
View Articleserver Board Intel S1200V3RPS
Hello! I bought server Board Intel S1200V3RPS. The problem occurred after installing the Intel®active system console (IASC_6.1_Build19) - when entering through the browser, the window for entering...
View ArticleRAID driver 4.5.6.1004
Have a server with C600+/C220+ series chipset with Intel RAID driver 4.5.6.1004. Cannot find the RAID management software, in fact, cannot even find Intel software on the Intel site with this version?
View ArticleNo BMC firmware installed
I have Server board S5520HCR. The BMC firmware does not appear to be installed. I have attempted to install various firmware packages, but they all leave the board unable to boot (nothing on the...
View ArticleHow can I change the terminal escape sequence for system1/sol1 on a RMM4?
2 of my RMM4 came with ^C instead of the usual ~. as the terminal escape sequence of sol1. How can I change this back? Every helpful reply is highly appreciated.
View ArticlePower failure - Server System R1304GZ4GC
Hello there, I had a lovely working server until today, I wanted to add a internal ssd into the case so I had to get the power supply for it. There is a OSD connector there for power so I found a...
View Article